深圳灣邊貿易進口代理Amptek XR-100CR X射線探測器價格優惠！Amptek X射探測系統，Amptek X光檢測儀， Amptek手執X射線探測器價格優惠！
TheXR-100CR系列產品由高性能 系列產品由高性能 系列產品由高性能 系列產品由高性能 系列產品由高性能 X射線探頭，前置放大器（）和致冷系統組成首次 射線探頭，前置放大器（）和致冷系統組成首次 射線探頭，前置放大器（）和致冷系統組成首次 射線探頭，前置放大器（）和致冷系統組成首次 射線探頭，前置放大器（）和致冷系統組成首次 射線探頭，前置放大器（）和致冷系統組成首次 射線探頭，前置放大器（）和致冷系統組成首次 射線探頭，前置放大器（）和致冷系統組成首次 射線探頭，前置放大器（）和致冷系統組成
TheXR-100CRis a high performancex-ray detector,preamplifier, andcoolersystem using a thermoelectrically cooled Si-PIN photodiode as an x-ray detector. Also mounted on the 2-stage cooler are the input FET and a novel feedback circuit. These components are kept at approximately -55 °C, and are monitored by an internal temperature sensor. The hermetic TO-8 package of the detector has a light tight, vacuum tight thin Beryllium window to enable soft x-ray detection. The XR-100CR represents a breakthrough in x-ray detector technology by providing "off-the-shelf" performance previously available only from expensive cryogenically cooled systems. |
Features
Additional Information
Accessories
| Applications
|
Figure 1.55Fe Spectrum taken with a 6 mm2/500 µm detector.
The resolution for the the 5.9 keV peak of55Fe is 145 eV FWHM to 230 eV FWHM depending on detector type and shaping time constant. SeeSelection Guide.
Theory of Operation
X-rays interact with silicon atoms to create an average of one electron/hole pair for every 3.62 eV of energy lost in the silicon. Depending on the energy of the incoming radiation, this loss is dominated by either the Photoelectric Effect or Compton scattering. The probability or efficiency of the detector to "stop" an x-ray and create electron/hole pairs increases with the thickness of the silicon.See efficiency curves.
In order to facilitate the electron/hole collection process, a 100-200 volt bias voltage is applied across the silicon depending on the detector thickness. This voltage is too high for operation at room temperature, as it will cause excessive leakage, and eventually breakdown. Since the detector in the XR-100CR is cooled, the leakage current is reduced considerably, thus permitting the high bias voltage. This higher voltage decreases the capacitance of the detector, which lowers system noise.
The thermoelectric cooler cools both the silicon detector and the input FET transistor to the charge sensitive preamplifier. Cooling the FET reduces its leakage current and increases the transconductance, both of which reduce the electronic noise of the system.
Since optical reset is not practical when the detector is a photodiode, the XR-100CR incorporates a novel feedback method for the reset to the charge sensitive preamplifier. The reset transistor, which is typically used in most other systems has been eliminated. Instead, the reset is done through the high voltage connection to the detector by injecting a precise charge pulse through the detector capacitance to the input FET. This method eliminates the noise contribution of the reset transistor and further improves the energy resolution of the system.
A temperature monitor diode chip is mounted on the cooled substrate to provide a direct reading of the temperature of the internal components, which will vary with room temperature. Below -20 癈, the performance of the XR-100CR will not change with a temperature variation of a few degrees. Hence, closed loop temperature control is not necessary when using the XR-100CR at normal room temperature. For OEM applications or hand held XRF instrumentation a closed loop temperature control is recommended. The Active Temperature Control is standard in Amptek electronics such as the PX5 and DP5/PC5.
XR100-CR Specifications
| General | |
| Detector Type | Si-PIN |
| Detector Sizes | 6 mm2(collimated to 4.4 mm2) 13 mm2(collimated to 11.1 mm2) 25 mm2(collimated to 21.5 mm2) See Selection Guide |
| Silicon Thickness | 500 µmSee efficiency curves |
| Collimator | Multilayer,click here for more information |
| Energy Resolution @ 5.9 keV (55Fe) | 145 eV FWHM to 230 eV FWHM depending on detector type and shaping time constant. See Selection Guide |
| Background Counts | <5 x 10-3/s, 2 keV to 150 keV for 6 mm2/500 µm detector |
| Detector Be Window Thickness | 1 mil (25 µm),or 0.5 mil (12.5 µm),See transmission curves |
| Charge Sensitive Preamplifier | Amptek custom design with reset through the H.V. connection |
| Gain Stability | <20 ppm/°C (typical) |
| Case Size | 3.00 x 1.75 x 1.13 in (7.6 x 4.4 x 2.9 cm),See mechanical dimensions |
| Weight | 4.9 ounces (139 g) |
| Total Power | <1 Watt |
| Warranty Period | 1 Year |
| Typical Device Lifetime | 5 to 10 years, depending on use |
| Operation conditions | 0°C to +40°C |
| Storage and Shipping | Long term storage: 10+ years in dry environment Typical Storage and Shipping: -20°C to +50°C, 10 to 90% humidity non condensing |
| TUV Certification Certificate #: CU 01 Tested to: UL 61010-1: 2004 R7 .05 CAN/CSA-C22.2 61010-1: 2004 | |
| Inputs | |
| Preamp Power | ±8 to 9 V @ 15 mA with no more than 50 mV peak-to-peak noise |
| Detector Power | +180 V (power supply should be able to produce between +100 to 200 V @ 1 µA) very stable <0.1% variation |
| Cooler Power | Current = 350 mA maximum, voltage = 4 V maximum with <100 mV peak-to-peak noise Note: the XR-100CR includes its own temperature controller |
