摩擦型扭力限制器Friction Te Torque Limiter
尺寸/Dimension
規格 . | 扭力范圍 TorqueRange Kgf.m | 標準 孔徑 Stock Bore mm | 孔徑 Max. Bore mm | 軸襯 長度 Bushing length | 軸襯外徑 Bushing Outside diameter | 中心構件 孔徑 Central Member Bore | D | DH | L | B | T | t | S | A | C | 調整 螺母 Adjust Nut | 調整 螺栓 Adjust Bolt | 固定 螺絲 Fixing Screw | 重量 Weight （kgf） |
SS200-1 | 0.3~1 | 8 | 14 | 3.6 | 30-0.024 -0.049 | 30+0.3 0 | 50 | 24 | 29 | 6.5 | 2.6 | 2.5 | 7 | - | 38 | M24 P1.0 | - | - | 0.2 |
SS200-2 | 0.7~2 | ||||||||||||||||||
SS250-1 | 0.7~2.8 | 10 | 22 | 4.5 | 41-0.010 -0.045 | 41+0.05 0 | 65 | 35 | 48 | 16 | 4.5 | 3.2 | 9 | 4 | 50 | M35 P1.5 | - | M5 | 0.5 |
SS250-2 | 1.4~5.5 | ||||||||||||||||||
SS350-1 | 2.0~7.6 | 17 | 25 | 6.5 | 49-0.025 -0.065 | 49+0.05 0 | 89 | 42 | 62 | 19 | 4.5 | 3.2 | 16 | 6 | 63 | M42 P1.5 | - | M6 | 1.2 |
SS350-2 | 3.5~15.2 | ||||||||||||||||||
SS500-1 | 4.8~21.4 | 20 | 42 | 6.5 | 74-0.05 -0.010 | 74+0.05 0 | 127 | 65 | 76 | 22 | 5.7 | 3.2 | 16 | 7 | - | M65 P1.5 | M8 3psc | M8 | 3 |
SS500-2 | 9.0~42.9 | ||||||||||||||||||
SS700-1 | 11.8~58.1 | 30 | 64 | 9.5 | 105-0.075 -0.125 | 105+0.05 0 | 178 | 95 | 98 | 24 | 7.7 | 3.2 | 29 | 8 | - | M95 P1.5 | M10 3psc | M10 | 6.7 |
SS700-2 | 22.8~110.6 |
摩擦型扭力限制聯軸器Friction Te Torque Limiter
尺寸表/Specification
規格 . | 扭力范圍 Torque Range Kgf.m | 轉數 Max. Rotational Frequency rpm | 普通內徑/Stock Bore | 內徑 Max. Inside Diameter | 鏈輪 Sprocket | D | DH | L | L1 | L2 | s | 重量 Weight (kgf) | ||
聯軸器側 Coupling Side | 扭力限 制器側 Limiter Side | 聯軸器側 Coupling Side | 扭力限 制器側 Limiter Side | |||||||||||
SS200-1C | 0.3~1 | 1200 | 8 | 8 | 31 | 14 | RS 40-16T | 76 | 50 | 55 | 24 | 29 | 7.5 | 1.0 |
SS200-2C | 0.7~2 | |||||||||||||
SS250-1C | 0.7~2.8 | 1000 | 13 | 10 | 38 | 22 | RS 40-22T | 102 | 56 | 76 | 25 | 48 | 7.4 | 2.0 |
SS250-2C | 1.4~5.5 | |||||||||||||
SS350-1C | 2.0~7.6 | 800 | 13 | 17 | 45 | 25 | RS 50-24T | 137 | 72 | 103 | 37 | 62 | 9.7 | 5.2 |
SS350-2C | 3.5~15.2 | |||||||||||||
SS500-1C SS500-2C | 4.8~21.4 9.0~42.9 | 500 | 18 | 20 | 65 | 42 | RS 60-28T | 188 | 105 | 120 | 40 | 76 | 11.6 | 12.3 |
SS700-1C | 11.8~58.1 | 400 | 23 | 30 | 90 | 64 | RS 80-28T | 251 | 150 | 168 | 66 | 98 | 15.3 | 31.0 |
SS700-2C | 22.8~110.6 |
鏈輪之配合參考表/ Applicable Sprockets
規格 . | 中心構件 孔徑 Central Member Bore | 少鏈輪節距和齒數/Min. Sprocket Pitch and Number of Teeth | |||||||||||||
3/8” -#35 | 1/2” -#40 | 5/8” -#50 | 3/4 -#60 | 1” -#80 | 11/4” -#100 | 11/2” -#120 | |||||||||
少鏈 輪齒數 Min Sprocket Teeth | 軸襯長度 Bushing length (mm) | 少鏈 輪齒數 Min Sprocket Teeth | 軸襯長度 Bushing length (mm) | 少鏈 輪齒數 Min Sprocket Teeth | 軸襯長度 Bushing length (mm) | 少鏈 輪齒數 Min Sprocket Teeth | 軸襯長度 Bushing length (mm) | 少鏈 輪齒數 Min Sprocket Teeth | 軸襯長度 Bushing length (mm) | 少鏈 輪齒數 Min Sprocket Teeth | 軸襯長度 Bushing length (mm) | 少鏈 輪齒數 Min Sprocket Teeth | 軸襯長度 Bushing length (mm) | ||
SS200 | 30+0.03 0 | 20 | 38 | 16 | 6 |
|
|
|
|
|
|
|
|
|
|
SS250 | 41+0.05 0 |
|
| 20 | 4.5 | 17 | 6.5 |
|
|
|
|
|
|
|
|
SS350 | 49+0.05 0 |
|
| 26 | 4.5 | 21 | 6.5 | 18 | 9.5 | 15 | 9.5 |
|
|
|
|
SS500 | 74+0.05 0 |
|
| 35 | 4.5 | 29 | 6.5 | 25 | 9.5 | 19 | 9.5 |
|
|
|
|
SS700 | 105+0.05 0 |
|
| 48 | 4.5 | 39 | 6.5 | 33 | 9.5 | 26 | 9.5 | 21 | 12.5 | 18 | 12.5 |
注意事項/te:
- 1. 中心構件之摩擦面須研磨加工以得額定之扭力，并成為平坦、平行，與內徑相垂直，任何灰塵，銹皮或油污為宜。
The friction surface of central member must be polished to gain the rated torque to provide flatness, parallel and perpendicularity to inside diameter, and to retain freed from dust, burr or oil.
- 2. 內環之選擇不可大于中心構件的寬度，中心構件厚度見表中之S尺寸。
The inner ring is greater than the width of central member. Please refer to the S dimension in the table to seek for the max. thickness of central part.
摩擦式扭力限制器
Friction Te of Torque Limiter
扭力值與鎖緊螺帽調整關系圖
Torque Value to Nut Packing Adjustment
