本儀器 用于檢測玩具可觸及到的位置是否存在危害的銳利尖點。
合標準：16 CFR 1500.48 ASTM F 963 4.8 EN.12 操作原理：試驗器有槽端有一寬0.04英寸長0.045英寸的矩形開口, 兩個參考尺寸尖銳度由被測該口的深度為0.015英寸深處的傳感頭, 并能克服彈力為0.5磅的彈簧使傳感頭再移動0.005英寸, 即被確認為尖銳點. 要求：槽開口不大于0.040×0.045英寸, 觸及深度不小于0.015英寸, 作用力不過1磅.：測試方法
1.尖點測試器調校程序
a.順時針旋轉/松開/鎖環。
b.順時針轉動尾蓋，直到紅色指示燈亮。
c.逆時針慢慢轉動尾蓋，直到指示燈剛好熄滅。
d.向前/后轉動尾蓋，確定指示燈剛好亮時確切位置。
e.參考尾蓋上的微米刻度線標注校正的位置。
f.逆時針轉動尾蓋5格刻度線（帽上兩短線之間的距離為一格）。
g.扭緊鎖環，直至緊靠尾蓋。
2.尖點測試程序
a.樣品在進行尖點測試前須在室溫為23±2℃、濕度為20%～70%的環境內放置4小時。
b.將放入尖點測試器測量槽內/握住測試物/垂直自由的施加共重1LBS（4.5N）的力，通過測試量槽位至測試。
判定：測試燈亮則為不合格
儀器型號：KXM20
The instrument for the detection of toys can be touched to the location of the existence of a risk of injury due to sharp cusp.
合標準：16 CFR 1500.48 ASTM F 963 4.8 EN.12
Standard: 16 CFR 1500.48 ASTM F 9634.8 EN.12
操作原理：試驗器有槽端有一寬0.04英寸長0.045英寸的矩形開口, 兩個參考尺寸尖銳度由被測該口的深度為0.015英寸深處的傳感頭, 并能克服彈力為0.5磅的彈簧使傳感頭再移動0.005英寸, 即被確認為尖銳點. 要求：槽開口不大于0.040×0.045英寸, 觸及深度不小于0.015英寸, 作用力不過1磅.：
Operating principle: the tester with a grooved end has a width of 0.04 inches long and 0.045 inches rectangular openings, two reference dimensions sharpness of a measured tip is inserted into the mouth of the depth sensing head 0.015 inches deep, and can overcome the elastic force of spring 0.5 pounds of the sensing head to move 0.005 inches, which is confirmed as the sharp. Requirements: slot opening is not greater than 0.040 x 0.045 inches, touch the depth of not less than 0.015 inches, force does not exceed 1 pounds:
測試方法
Test method
1.尖點測試器調校程序
1 sharp point tester calibration procedure
a.順時針旋轉/松開/鎖環。
A. clockwise / release / lock ring.
b.順時針轉動尾蓋，直到紅色指示燈亮。
B. clockwise rotating tail cover, until the red indicator light.
c.逆時針慢慢轉動尾蓋，直到指示燈剛好熄滅。
C. clockwise slowly turn the tail cover, until the light was extinguished.
d.向前/后轉動尾蓋，確定指示燈剛好亮時確切位置。
D. forward / back turn tail cover, determine the indicator lamp just bright when the exact location.
e.參考尾蓋上的微米刻度線標注校正的位置。
The E. reference tail cover on the micron scale line marking the location correction.
f.逆時針轉動尾蓋5格刻度線（帽上兩短線之間的距離為一格）。
F. counterclockwise tail cover 5 grid scale line (Cap two short distance as one).
g.扭緊鎖環，直至緊靠尾蓋。
G. screw lock ring, until close to the tail cover.
2.尖點測試程序
Test procedure 2 cusps
a.樣品在進行尖點測試前須在室溫為23±2℃、濕度為20%～70%的環境內放置4小時。
In the A. sample were sharp point testing must be at room temperature is 23 ± 2 ℃, humidity 20% ~ 70% environment placed within 4 hours.
b.將放入尖點測試器測量槽內/握住測試物/垂直自由的施加共重1LBS（4.5N）的力，通過測試量槽位至測試。
B. will tip into the sharp point tester measuring tank / hold test / vertical free applied a total weight of 1LBS (4.5N) force, through measuring slot to test tip.
判定：測試燈亮則為不合格
Judge: test lights for unqualified
儀器型號：KXM20
The instrument model: KXM20
